Common, well-proven and clean technology – both as a complete unit and in terms of its individual components. Robust and sturdy for installation in remote locations. As labor free as possible, easy to use and operated by trained but mostly unskilled operators. Require minimal pre-processing, limited need for prior sorting, crushing or shredding.Capable of handling mixed solid waste streams (non-recyclable waste with some mix of organic waste, garden waste, burnable materials such as waste wood and clothing). It can accommodate large variations in waste composition and calorific value.Operated on a daytime shift basis, five (5) days per week. Have very low unburned materials in the slag.Economical to operate and maintain and have a low and efficient fuel consumption. Have an operation manual in English.Catalogues/brochures are required. Detail Specifications for Waste Incinerators:The equipment should have a minimum life time operation often (10) years in a tropical environment.Average loading capacity of 1,000 kg/day with maximum loading capacity of 1,200 kg.
Incinerator units shall include an integral and mechanized bottom ash removal system.Ali the measuring devices attached to the incinerator should have digital display and should have provision of connecting to the recording system, which should include fuel meter and separate energy meter.Include designed pollution control devices such as scrubbers, filters or electrostatic precipitators to achieve emission limits.Each unit shall include a complete vertical exhaust and stack system 6-12 m above ground level with exhaust exit velocity of not less than 10 meters per second.Include clearly readable system operation panels. Spare parts:Each incinerator shall be supplied with all necessary spare parts required for two (2) years of operation (one set for each unit).Mandatory spare parts, for all the incinerators as a minimum, shall include: thermocoupletemperature gaugefire ropeburnerinduction air fandigital temperature display panel
Nominal burning rate shall be 100 -140 kg/hr with 8 hour daily operating cycle of ash removal, pre-heat and burn with continuous loading.Primary power source shall be electricity but capable of using diesel fuel as a supplemental fuel.The waste incinerators shall be designed for 3 Phase, 380-400 V, 50 Hz electricity supply.Should have dual combustion chambers with gas temperature achieve 1000 C for retention time at least 2 second,Have a thermal efficiency of not less than 85%.All metal surfaces (except combustion chamber internal fittings) shall be either galvanized, enameled, painted or otherwise treated against atmospheric and process induced corrosion.The incinerator combustion chambers should be designed for easy maintenance of all internal parts including the refractory and insulation. Materials used in the individual parts of the incinerator shall be heat resistance and also be protected against oxidation, corrosion, etc.Primary and secondary chambers preferably have rounded inside corners to avoid the formation of dead zone or cold pockets.Generate residual incinerator ash conforming to <10% by volume and <25% by weight of the waste incinerated.Achieve a Total Organic Carbon (TOC) content in the slag and bottom ashes of less than 3%. Combustion Efficiency (CE) at least 99%.
WWW.HICLOVER.COM｜Waste Incinerators ｜Auto Roll Air Filters Nanjing Clover Medical Technology Co.,Ltd. Tel: +86-25-8461 0201 Mobile: +86-13813931455(whatsapp/wechat)Website: www.hiclover.com Email: sales@hiclover.comEmail: hicloversales@gmail.com Item Specification Model CA-200 Main Product List Primary Combustion Chamber Secondary Combustion Chimney Incinerator Control Case Chimney:5.0Meters *(upgrade to Stainless Steel, free cost) Italy oil burner: 02 units Oil Tank: 1500Liters 70% New Second hand, ISO 20′ Container * 1 set Items/Model CA200 Picture Principle […]
Item Specification Model A900 Internal Dimensions 120 x 90 x 85 CM Suit for Animal Cat – yes Dog – yes Pig – small Cow – no Main Product List Primary Combustion Chamber Secondary Combustion Chamber Mix-Combustion Chamber Smoke Filter Chamber Incinerator Control Case Chimney:5.0Meters *(upgrade to Stainless Steel, free cost) Italy oil/gas burner: 02 […]
Incinerator Model TS50 PLC, Overview This model is small-scale animal cremation equipment for small – middle animal. Construction is dual/double combustion chamber with 02 units oil burner, batch load incineration equipment. Waste feed chamber is 560Liters (0.56m3, TS50 PLC). Primary & Secondary combustion chambers and smoke filter chamber. Batch load on the bottom of chamber. […]
This model is small-scale animal cremation equipment for small animals. Construction is dual/double combustion chamber with 02 units oil/gas burner, batch load incineration equipment. Animal feed chamber is 600Liters (A600). Primary & Secondary combustion chambers and included mix-combustion chamber, smoke filter chamber with Refractory Concrete chamber. Batch load on the bottom of chamber. Model A600 […]
Item Specification Model YD-10 Main Product List Combustion Chamber Control Case Stack: 3.0Meters Oil burner: 02 units Oil Tank (if oil fuel):50Liters Equipment Technical Specifications Model YD-10 Picture Feed Capacity Average 20 kgs per feed Burning Rate Average 15 kgs per hour Burning Time per Feed 2 hours Voltage 220V Power 0.5Kw Fuel Diesel oil […]
Model WS-100 Picture Burning Rate Average 100 kgs/hour Feed Capacity Average 200 kgs Primary Combustion Chamber 1200 Liters Secondary Combustion Chamber 500 Liters Mix Combustion Chamber Yes Smoke Filter Chamber Wet Scrubber System Feed Mode Manual Voltage 220V Power 2Kw Fuel Type Diesel Oil/ Natural Gas/LPG Burner Italy Original Oil Consumption (Diesel Oil) 14--28 kg/hour […]
HICLOVER Fighting COVID-19 CE ISO
