Waste Incineration Treatment Average 150 kg/hour


WWW.HICLOVER.COMWaste Incinerators Auto Roll Air Filters
Nanjing Clover Medical Technology Co.,Ltd.

Tel:  +86-25-8461 0201   

Mobile: +86-13813931455(whatsapp/wechat)
Website: www.hiclover.com  
Email: sales@hiclover.com

Items/Model

TS150(PLC)

Principle

Waste Incineration Treatment

Burn Rate

Average 150 kg/hour

Feed Capacity

Average 250kg/feeding

Control Mode

PLC(Programmable Logic Controller Incinerator)

Combustion Chamber

1300L

Internal Dimensions

120x100x110cm

Secondary Chamber

600L

Smoke Filter Chamber

Yes(Dry Scrubber)

Feed Mode

Manual

Voltage

220V

Power

0.7Kw

Oil Consumption (kg/hour)

Average 20.4

Gas Consumption (m3/hour)

***

Temperature Monitor

Digital Display

Temperature Protection

Yes

Oil Tank

200L

Feed Door

80x60cm

Chimney

10Meter

Chimney Type

Stainless Steel

1st. Chamber Temperature

800-1000

2nd. Chamber Temperature

1000-1200

Residency Time

2.0 Sec.

Gross Weight

6000kg

External Dimensions

260x150x180cm

For incineration, general and pathological
100 C 120 kg/h burn rate
Two  combustion chambers type; primary  and Secondary, controlled/forced combustion air 
type with a flue gas emission scrubbing unit
Minimum 8 hours daily
From 850 0C to 1200 0C, Automatic controlled
5 to 10%
Constructed from heavy duty mild or aluminized  steel
Or equal and approved equivalent
Refractory material lining similar or equal to calcium 
Silicate and hot face combination of heavy duty brickwork
Fixed hearth type complete with gratings, concave bottom and charging door, lined with refractory material
Suitable for manual loading of wastes and with smooth 
Dear seal equivalent of Ceramic seals with hinges.
Automatic, Electric type
Provided, for removing resultant bottom ash leftovers                              from the Primary chamber
Provided
Manual loading of waste
Fully automatic, with fuel, temperature and speed  controls with ignition system  flame detector                                                        
 Air fan Complete with safety features, flame failure                                                                    Diesel fired fuel injector type                                               
Flange mounted
Provided.  3 phase for supplying excess combustion air through the distribution system with speed control system
Minimum exit 850 0C
To be provided with protective glass type
Constructed from heavy duty mild or aluminized steel or equal and approved equivalent
Refractory material lining
Above 850 0C, controlled electronically
> 2 second at minimum 850 0C
Provided, 
Diesel fired,                                                                      
Fully automatic, with fuel, temperature and speed controls 
With ignition system
Flame detector
Air fan       
Complete with safety features, flame failure
Diesel fired fuel injector type
Flange mounted
Provided, Venturi type, for cooling the flue gases
Provided for supplying combustion and creating a
negative drift and turbulences with variable speed control
Maximum  1600 0C       
Fully automatic with microprocessor based control
unit (PLC) automating all operations of the incinerator
Capable of monitoring all incinerator parameters
With large LCD or similar for display of all progress
Parameters  i.e. temperature of primary and second chambers , turbulence and time
With status lamp
With user of defined and differed programmed operating cycles for different type of loads/conditions
With safety interlocks, display of errors and visible and audio alarms.
System for continuous  emission monitoring
Supply and install isolator switch 100A, 3 phase, 415V, 50Hz, for the incinerator unit , including all necessary cables 10m
Supply and install distribution board 100 A, 3 phase 415V, 50Hz, complete with MCBs suitable for the rating of 
the incinerator unit and associated equipment.  Wiring   to be done according IEE regulations.                                                                    

Could not authenticate you.