chinese incinerator manufacturers Containerized


Model

CA100

Waste Treatment

Waste Incineration Treatment

Feed Capacity

Average 100 kgs per feed

Burning Rate

Average 100 kgs per hour

Burning Time per Feed

Average 1 hour

Control Mode

PLC(Programmable Logic Controller Incinerator)

Voltage

220V

Power

0.7Kw

Fuel

Diesel oil

Burner

Italy Burner

Feed Mode

Manual

Temperature Monitor

Digital Display

Fuel consumption (Oil)

Average 16.6 Kgs/Hour

Internal Dimensions

100x80x70cm (Primary Chamber)

External Dimensions

230 x 130 x 155cm (main body)

Waste combustion chamber

560Liters

Post Combustion Chamber

280Liters

Oil Tank Capacity

200 Liters

Door Opening

70 x 50cm

Chimney

5.0M

Gross Weight

4500kgs

Chamber Material

Firebrick ,Refractory Concrete

Max. Heat Value

166,000Kcal/Hr.

Operation Technical Specifications

Solid Chamber temperature

8000C -10000C

Gas Chamber temperature

10000C -12000C

Chamber Anti-Rate

14500C

Residency time

2.0 Sec.

Burning efficiency

98%

Waste Lower Calorific Power

3000Kcal























Minimum 50-100% moisture
Blood, drips, human faces
Human organs
Human tissues
Majority of Cancer treatment wastes
Majority of Pharmaceuticals
The proposed incinerator units must be complete and include all of the key features listed below and all of the associated support services and interconnections
The forecasted feedstock loads, and daily loading rates are generally summarized as
• Mixed general, clinical and incinerable hazardous wastes with a wide range of calorific values and densities.  The majority of the wastes will be of a general municipal nature, with up to 15% by volume of medical wastes and up to 5% by volume of incinerable hazardous wastes.  The content of the combustible matter will be above 60% and moisture content below 30%.  The wastes will be crudely pre-mixed by selective loading from different waste streams prior to incinerator loading. 
• Wastes either small enough to fit within a 60 litre waste sack or broken up or shredded to less than 300mm in size.
• Operation on a daytime shift basis, 5 days per week.
The incinerator units shall include a temperature based electronic combustion control system that utilizes temperature and other data to inform automated or programmed cycling through the standard burn cycle: pre-heat, burn with waste addition, burn completion, cool-down. The system shall be capable of varying auxiliary fuel and air supply in both combustion chambers to achieve optimum combustion conditions. As far as practicable, the incinerator shall be of a plug and play type for ease of installation and commissioning in remote locations.
“The control system shall have a separate push button-based work station, which shall be located adjacent to the loading bay and protected from weather and impact damage. The system shall allow for rapid and straightforward intervention by the operator if the automatic system is not achieving the desired results during a burn cycle. 


• An 8 hour daily operating cycle of ash removal, pre-heat and burn with continuous loading if required.  The automated burn completion and cool down cycle will take place overnight.


  • RT @XHNews: Timeline shows critical moments of China-U.S. #COVID19 interaction To say China did not cooperate is a total LIE https://t.co/v…
  • RT @Jackesoneric: 兵马俑VS自由女神!新华社视频在国外火了 https://t.co/7O8LmDBVvK
  • ES Fiber Production Line and 400mm Melt blown Production Line and 1600mm Melt blown Production Line and and ... -… https://t.co/7G9USyMfxT
  • RT @DrTedros: From Seychelles 🇸🇨 to Djibouti 🇩🇯, Somalia 🇸🇴 to Madagascar 🇲🇬; face shields, gloves, goggles, gowns, masks, medical aprons a…
  • RT @PeterASinger: What has @WHO done on #COVID19? — shipped >2 m pieces of PPE — supplied 1.5 m diagnostics — provided 1.2 m courses to hea…